Schedule A Free Estimate

 

 

Just how do you really feel in regards to A Step-by-Step Guide to Installing a Bathtub?

Setting up a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard task. If the old tub is readily obtainable, the task can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually qualified on your own for the work and also are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have actually currently gotten a new tub and do not require to alter the arrangement of your previous water supply pipelines.
Your devices and material list must make up the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installment

First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last placement.

 

 

Removing Old Taps

If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Setting up the Bath tub

Using the two wooden boards under its feet, position the bath tub in the required setting. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the tub up until the spirit level reads level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other faucet.
Activate the water supply and check all joints and brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait up until the tub has been utilized at least once as this will resolve it right into its final position.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bathtub

In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bath tub with water before securing, to permit the movement experienced when the tub is in usage. The sealant can split fairly early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water-proof glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed reading our article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for taking a few minutes to read through our piece. Enjoyed our piece? Please share it. Help someone else find it. Many thanks for taking the time to read it.

Pricing